Guitar

Software

  • Ditto X4 Looper

    Firmware

    + Show version history + Hide version history
    Changes in version 1.1.00

    Added MIDI Control (use MIDI Channel 4)

    • CC3 Looper 1 Rec/Dub/Start
    • CC9 Looper 1 Stop
    • CC14 Looper 1 Clear
    • CC15 Looper 1 Level
    • CC20 Looper 1 Hold to Store
    • CC21 Looper 1 Clear Backtrack
    • CC22 Looper 2 Rec/Dub/Start
    • CC23 Looper 2 Stop
    • CC24 Looper 2 Clear
    • CC25 Looper 2 Level
    • CC26 Looper 2 Hold to Store
    • CC27 Looper 2 Clear Backtrack
    • CC28 Decay "Level"
    • CC29 All Loops Stop
    • CC30 All Loops Clear
    • CC31 FX On/Off
    • CC85 Parallel/Serial Toggle

    Program Change for Effect Selection

    • PG1: FX1
    • PG2: FX2
    • PG3: FX3
    • PG4: FX4
    • PG5: FX5
    • PG6: FX6
    • PG7: FX7
    1. Allows both fade in and fade out: Press fade to start fade, press during progress to force the finish of a fade, press again to start fade-in, press again to force finish of the fade in.
    2. Allow hold-to-erase while playing after initial record before first undo layer is created.
    3. Free mode now allows serial mode to switch playback instantly.
    4. Now exports 24bit files instead of 32bit.
    5. Don't cancel undo on stop button (only after double tap to stop).
    6. Properly schedule 2x and half speed in serial mode.
    7. Only employ intelligent "groove return" on reverse and speed changes when midi sync is active.
    8. Increased fade in/out time.
    9. Double Tap Time reduced to make it easier to tap to stop.
    10. Queued mode record set now blinks red light while waiting to set.
    Ditto X4 Looper Firmware Windows - Version 1.1.00 - 11 MB
    Released: Wednesday, October 12, 2016
    + Ditto X4 Update Procedure - Ditto X4 Update Procedure

    To update your Ditto X4, you will require a Mac or PC with a standard USB Interface and Ditto X4's specified DC power supply.  First download the latest Ditto X4 firmware update installer for your operating system from the tc electronic website and store it on your computer's hard-disk.

     

    Do following steps before you start the firmware update application on your Mac/PC:

     

    1. Unplug all cables from the pedal.

    2. Quit any MIDI related applications running on your Mac/PC.

    3. Connect the pedal to a Mac/PC with the USB cable.

    4. Press and hold the LOOP1 footswitch on the pedal.

    5. Insert the DC power supply plug.

    6. When the LOOP1 footswitch LED turns from Orange to Off, release the LOOP1 footswitch.

    7. When all four LEDs turn green the pedal is ready to be connected via USB.

     

    Now your Mac/PC will recognize the pedal which is ready to receive a new firmware:

     

    8. Launch the downloaded firmware update application.

    9. Select Ditto X4 from the output device dropdown box (***).

    10. Press the update button when it turns green.

    11. Wait for the progress bar to reach 100% and for the pedal to automatically restart.

     

    ***: If you are using Windows XP, select "USB Audio Device".

    Ditto X4 Looper Firmware Mac - Version 1.1.00 - 12 MB
    Released: Wednesday, October 12, 2016
    + Ditto X4 Update Procedure - Ditto X4 Update Procedure

    To update your Ditto X4, you will require a Mac or PC with a standard USB Interface and Ditto X4's specified DC power supply.  First download the latest Ditto X4 firmware update installer for your operating system from the tc electronic website and store it on your computer's hard-disk.

     

    Do following steps before you start the firmware update application on your Mac/PC:

     

    1. Unplug all cables from the pedal.

    2. Quit any MIDI related applications running on your Mac/PC.

    3. Connect the pedal to a Mac/PC with the USB cable.

    4. Press and hold the LOOP1 footswitch on the pedal.

    5. Insert the DC power supply plug.

    6. When the LOOP1 footswitch LED turns from Orange to Off, release the LOOP1 footswitch.

    7. When all four LEDs turn green the pedal is ready to be connected via USB.

     

    Now your Mac/PC will recognize the pedal which is ready to receive a new firmware:

     

    8. Launch the downloaded firmware update application.

    9. Select Ditto X4 from the output device dropdown box (***).

    10. Press the update button when it turns green.

    11. Wait for the progress bar to reach 100% and for the pedal to automatically restart.

     

    ***: If you are using Windows XP, select "USB Audio Device".

Manuals